Does The Ford 3000 Have A Hydraulic Filter

FORD 3000 HOW Exercise You REMOVE THE HYRAULIC FILTER

View previous topic :: View side by side topic
Author	Message
DUCKMEAT New User Joined: 20 Aug 2009 Posts: fifteen Report to Moderator	Posted: Mon Aug 31, 2009 seven:32 am   Post subject: FORD 3000 HOW DO You lot REMOVE THE HYRAULIC FILTER Can SOMEONE PLEASE TELL ME HOW TO GET TO THE THING .... THANKS
Back to top
Mathias NY Tractor Expert Joined: 08 Oct 2004 Posts: 1538 Location: Upstate NY Written report to Moderator	Posted: Mon Aug 31, 2009 8:59 am   Mail service subject: Re: FORD 3000 HOW Do YOU REMOVE THE HYRAULIC FILTER Endeavour searching a piffling in the archives of the Ford forum. The link below is to a tread I started a while agone for the Hydraulics on my 3000. My issue still isn't resolved, merely I have narrowed it down to the position/draft control adjustments. To get at both hydraulic filters, drain the fluid, remove the seat, remove the transmission top cover, and remove the PTO shaft. I also removed the left floor board, but I tin't remember if that was necisary. I also call up there was an admission cover on the left side that needed to be removed. The fastened picture is of my tractor after I changed both filters. The rear of the tractor is toward the right, the upper pointer is for the outlet filter, and the lower arrow is for the intake filter. Onetime thread
Dorsum to top
DUCKMEAT New User Joined: 20 Aug 2009 Posts: 15 Report to Moderator	Posted: Mon Aug 31, 2009 11:24 am   Post subject: Re: FORD 3000 HOW DO YOU REMOVE THE HYRAULIC FILTER Mathias NY wrote: (quoted from postal service at 09:59:44 08/31/09) Try searching a lilliputian in the archives of the Ford forum. The link below is to a tread I started a while ago for the Hydraulics on my 3000. My issue still isn't resolved, but I have narrowed it down to the position/draft control adjustments. To get at both hydraulic filters, drain the fluid, remove the seat, remove the manual height cover, and remove the PTO shaft. I likewise removed the left flooring board, but I can't remember if that was necisary. I also recollect at that place was an access cover on the left side that needed to be removed. The attached motion-picture show is of my tractor after I changed both filters. The rear of the tractor is toward the right, the upper arrow is for the outlet filter, and the lower arrow is for the intake filter. One-time thread Quote: Cheers Then MUCH .. IV TAKEN THAT Circular COVER OFF THE SIDE .. Can I Take THE FILTERS OFF FROM Here ... AND WILL HY TRAN Piece of work
Dorsum to top
Mathias NY Tractor Expert Joined: 08 Oct 2004 Posts: 1538 Location: Upstate NY Report to Moderator	Posted: Mon Aug 31, 2009 12:51 pm   Post subject: Re: FORD 3000 HOW Do YOU REMOVE THE HYRAULIC FILTER I don't think it will be possible to remove the filters without removing the top plate. You volition demand all the room you tin can get to maneuver the filter associates around the bulldoze shaft. I was only able to get mine out after removing the PTO shaft and bending the mounting tab on the filter itself. Information technology'due south a very tight fit and unless you take having hydraulic bug, I wouldn't even attempt to clean it. Generic Hy-tran might be ok to employ. Check the cantankerous reference table on the oil, if the Ford 134 fluid is listed it volition exist fine. Otherwise, I wouldn't trust it. It sounds similar y'all might exist new to working on tractors, I highly recommend ownership an owners manual and an I&T service manual. These will be you best references on using and working on the tractor. Skillful luck.
Back to acme
southern_boy1975 New User Joined: 27 Nov 2017 Posts: 1 Study to Moderator	Posted: Monday Nov 27, 2017 12:16 pm   Post bailiwick: Re: FORD 3000 HOW Practise YOU REMOVE THE HYRAULIC FILTER Mathias NY wrote: (quoted from postal service at 13:51:xiii 08/31/09) I don't think it will be possible to remove the filters without removing the pinnacle plate. Y'all volition demand all the room you can get to maneuver the filter assembly around the bulldoze shaft. I was just able to get mine out after removing the PTO shaft and angle the mounting tab on the filter itself. Information technology's a very tight fit and unless yous have having hydraulic problems, I wouldn't fifty-fifty try to clean information technology. Generic Hy-tran might be ok to use. Check the cross reference table on the oil, if the Ford 134 fluid is listed it will exist fine. Otherwise, I wouldn't trust it. It sounds similar you lot might exist new to working on tractors, I highly recommend buying an owners manual and an I&T service manual. These volition be you best references on using and working on the tractor. Adept luck. Hi, you say they are not worth cleaning without hydraulic issues but what if you are finding a lot of micro metal particals in the case bottom? I had to remove the side plate to locate function of the pto housing snap ring that had broke off. I found a couple of pieces in the rear section and a couple in the hydraulic area.. Would you lot make clean them at that point or only wipe the housing out and reassemble? Simply looking for opinion..... Thanks
Back to elevation
Display posts from previous:

Does The Ford 3000 Have A Hydraulic Filter,

Source: https://forums.yesterdaystractors.com/viewtopic.php?t=525422

Posted by: nelsonhadvaid.blogspot.com

Share this post